Airfix : White M3A1 Half-track. [Part 2]

Okay, this kit got much worse. Whilst I said last time, the chassis went together nicely, not so much for the body-work. it's been a right pain to put together.

I started, as the instructions said, by putting the walls of the thing together and attaching the back. Easier said than done I'm afraid. i thought about using blu-tack to hold the thing in place, I've noticed with a few previous models that blu-tack causes the glue to run and scar the model. I then thought about masking tape, but I didn't fancy cutting it to spec (mainly cause I'm lazy).

 
In the end Dad suggested using good old Lego. A favourable idea as I knew where the lego was, it was all sorted into boxes, but also since I needed the real panel to be 90 degrees to the back. Good old Lego.

This was the easiest part of the hull assembly, the cockpit. Mainly because it's only two pieces, it glues together nicely. Sadly the same isn't true about the rest of it. there's some odd shapes involved with the main hull which makes it harder than it should be to put together, but a lot of the pieces didn't seem to fit.

 The whole thing, once assembled, looks nice, it's not all been put together yet, there's still a few parts to glue on. But it's coming together nicely!

Airfix : White M1A3 Half Track

Okay, so, first of all, I've not posted in ages, primarily this is because I've been busy or too lazy to work on the Marder.

I have however been working on small 1/72 stuff. Including a Jagdpanther and a SdKfz251/1. These are both built and painted now, and I'd forgotten about the blog. So I didn't think to document it. Still started a new one today when I remembered the blog. So I took pictures and such!

Onto the good stuff! The instructions are clear. Although I did stick the tracks on upside-down at first through lack of attention. I was disappointed by the amount of flash on some pieces. (Pictures to the left.) So I set about them with my craft knife, sandpaper and liquid poly tidying up edges and gluing parts together.




So far I've only put the undercarriage together. It was easy, apart from the exhaust, which requires a bit of a steady hand and a large amount  of liquid poly... But it does go together nicely, that aside.

I'll do some more work on it shortly, might put a post up tomorrow, or I might put one up tomorrow, depends how much I do.

The Marder III

So here's the first model to be put into blog form! I've made a few 1/72nd scale models over the last two or three weeks, and decided I'd gotten enough practice in to attempt something a little bigger. So I dug out the Tamiya Marder III my dad bought for me a while ago. 

Courtesy of the Bundesarchiv

I didn't know a whole lot about the Marder III before I'd opened the box, only little bits I'd picked up from games.  I thought it'd be a good idea to read up on it before I started, so I headed to good old Wikipedia, the starting point for all projects! In doing so I discovered a little about the background of the Marder III. I'll briefly outline below for anyone who's interested to read, but obviously more information available on Wikipedia.

The Marder III was a German Tank Destroyer put into service around 1942 and used on all fronts of the war. It was made using a Czech Panzer 38(t) chassis and mounting a Pak 40 75mm gun on top (or a 7,6cm Russian canon before the Pak 40 was widely available.)  Being a Tank Destroyer it was designed to engage tanks from long range and knock them out before being attacked itself, hence it was lightly armoured. But with a large armament to punch through enemy armour.

It was rushed into service as a stop-gap measure against Russian tanks of the time (The T-34) and continued to be used throughout the war.

Enough background I think on to the kit itself. It's seems to be well made, (a common trait of Tamiya I've read) with very little flash on the parts ( flash : excess plastic on the parts from the moulding process), and good detailing on the parts. Thanks to my dad, who has been making models far longer than I have, I decided to have a poke round on the web for people who've made the model before to see what they've done, and also to look for after-market parts which would be an improvement on the parts 'out of the box'. 

I didn't get much done on it today, as I was taking it slowly, and I'd been playing games all morning... But here's the parts still on the sprue.